MAIN PAGE > PRODUCTS > HT-350 > MATERIAL SAFETY DATA SHEET BACK ONE

HT-350
Epoxy & Urethane
Paint Remover
IDENTIFICATION

HAZARDOUS INGREDIENTS

PHYSICAL DATA

FIRE & EXPLOSION HAZARD DATA

HEALTH HAZARD DATA

REACTIVITY DATA

SPILL, LEAK OR WASTE DISPOSAL PROCEDURES

SPECIAL PROTECTION

SPECIAL PRECAUTIONS

SECTION I

Identification

Manufacturer:
Hydrochemical Techniques Inc
P.O.Box 2078
Hartford, Connecticut 06145

Product Name:
Hydroclean HT-350 Epoxy & Urethane Paint Remover

Emergency Telephone Number: (800) 278-7681

Date Prepared: December 15, 2013

SECTION II

Hazardous Ingredients

Chemical Name:
Methylene Chloride - cas# 75-09-2 - % 66.0 - TLV (UNITS) 25 PPM
Toluol - CAS Number 108-88-3 - % 5.0 - TLV (UNITS) 100 PPM
Methanol - CAS Number 67-56-1 - % 9.0 - TLV (UNITS) 200 PPM
Formic Acid - CAS Number 64-18-6 - % 1.0-5.0 - TLV (UNITS) 5 PPM

SECTION III

Physical Data

Boiling Point: (°F) 105°
Vapor Pressure: (mm hg.) 340
Vapor Density: (air = 1) 2.93
Solubility in Water (20°C): 100%
I.D. Number: UN 1593
Appearance & Odor: colorless liquid with a mild chlorinated odor.
Specific Gravity: 1.0
Percent, Volatile/Volume: 91.0%
Evaporation Rate: (ethylether=1): Not Available
pH: 5.2
U.S. Dot Hazard Class: orm-a

SECTION IV

Fire & Explosion Hazard Data

Flash Point (Method Used): Nonflammable
Flammable Limits: Not Applicablep
Extinguishing Media: Not Applicablep
Special Fire Fighting Procedures: Wear NIOSH/MSHA approved self-contained breathing apparatus. Wear a full face piece operated in pressure demand or other positive pressure mode and full body protective clothing when fighting fires.

SECTION V

Health Hazard Data

Threshold Limit Value: 25 PPM

Effects of Overexposure:
Inhalation - may cause irritation.
Skin - can cause irritation or burns from use.
Eyes - can cause painful irritation or burns from prolonged and repeated use. Caution - people with heat heart problems should not use this product.

Emergency & First Aid Procedures:
Inhalation - Remove victim to fresh air and seek medical attention.
Skin - Wash with water - if irritation persists, seek medical attention.
Eyes - Flush with plenty of water for 15 minutes, holding eyelids open. Seek medical attention.

SECTION VI

Reactivity Data

Stability: Stable

Incompatability (Materials to Avoid): Do not mix with alkline based products.

Hazardous Decomposition Products: If mixed with other products, could emit chlorine.

Conditions to Avoid: Thermal degradation will emit hydrogen chloride, carbon monoxide and chlorine.

SECTION VII

Spill, Leak or Waste Disposal Procedures

Spills or Leaks: Small Spills - Mop up, remove to out of doors. Large Spills - Evacuate area. Contain liquid transfer to metal container. Keep out of water supply.
Waste Disposal: Dispose of contained spill in accordance with applicable state and federal regulations.

SECTION VIII

Special Protection

Respiratory: Below 25 PPM - none. Above 25 PPM use self contained breathing apparatus.
Ventilation: Provide proper ventilation to keep exposure below the threshold limit value (50 PPM).
Gloves: Wear neoprene or PVC gloves.
Eye: Wear full plastic face shield or goggles.
Other Protective Equipment: Hard hats and full wet suits are always recommended.

SECTION IX

Special Precautions

Handling & Storage: Store in cool place.
Other precautions: Avoid breathing strong vapors. Protect eyes and hands. Open container slowly in case of possible pressure build up.
DANGER!!! Epoxy & urethane paint remover contains methylene chloride, which is a substance suspected to be a cancer causing agent in humans.
MAIN PAGE > PRODUCTS > HT-350 > MATERIAL SAFETY DATA SHEET : TOP

http://www.hydroclean.com
All information and photos are copyright Hydroclean.
No material may be reproduced without express written permission from Hydrochemcial Techniques, Inc.

HYDROCLEAN
Hydrochemical Techniques, Inc.
PO Box 2078
Hartford, CT 06145
Tel: 800-278-7681 • 860-527-6350
Fax: 860-527-4067
info@hydroclean.com